produktbilde
produktbilde
produktbilde
produktbildeproduktbildeproduktbilde
Artikkelnummer: JBL-CBT200LA-1-WH

CBT passiv kolonnehøyttaler med 32 stk 2" elementer, hvit

Den patenterte CBT teknologien gir høyttaleren meget jevn frekvensrespons innenfor sitt dekningsområde og reduserer lobing utenfor.

Veil. pris: Kr 24 690,- eks. mva. Veil. pris: Kr 30 863,- inkl. mva. Netto: Kr 24 690,- eks. mva.
Ikke på lager
Frekvensbånd:
Farge:
Bjørn Magne Idland

Bjørn Magne Idland

SALG | TEKNISK SUPPORT

  • Avdeling Installasjon
  • Telefon 23 23 28 58
  • Mobil 95 80 84 94
  • Produkttekst
  • Spesifikasjoner
  • Datablader

Høyttalerens vertikale spredning kontrolleres med et avansert passivt filter som gir hvert element i kolonnen riktig nivå og fase.

Den vertikale spredningen kan settes til 15 grader eller 30 grader. De to seksjonene kan justeres individuelt, slik at den vertikale spredningen kan gjøres asymmetrisk. Man kan f.eks. sette den øverste seksjonen til Narrow slik at lyden kastes langt bakover, og den nederste seksjonen kan settes på Broad for å dekke større område nærmere høyttaleren.

Den innebygde EQ'en gir enten en flat respons til musikkbruk, eller et løft i presensområdet for talebruk.

100V trafo eller direkte 8 ohms tilkopling (separat for de to seksjonene). 
Veggbrakett med justerbar tilt er inkludert. 
Brakett for flush montering er tilleggsutstyr.

Components Thirty-two 50 mm (2 in) Full-Range Drivers
Frequency Range (-10 dB) 80 Hz – 20 kHz
Frequency Response (±3 dB) 130 Hz – 18 kHz (narrow coverage, music mode setting)
Coverage - Vertical Narrow Mode:
15° (500 Hz – 16 kHz, +15°/-2° [<60° down to 220 Hz, <90° down to 140 Hz])
Broad Mode:
30° (400 Hz – 12 kHz, +15°/-8°, [<60° down to 220 Hz, < 90° down to 140 Hz])
Asymmetrical Progressive-Gradient Mode:
(Top speaker module set at “Narrow” and bottom speaker module at “Broad”, for “J-type” coverage, sending higher sound levels toward the far area of the listening space): 22.°(+7° from aiming axis up; -15° from aiming axis down, 300 Hz – 12 kHz, +15°/-8°, [<60° down to 220 Hz, <90° down to 140 Hz])
Coverage - Horizontal 150° (ave, 1 kHz – 4 kHz, ±20°)
Sensitivity - Narrow (speech mode): 95 dB (2 kHz – 5 kHz)
(music mode): 92 dB (150 Hz – 18 kHz)
Sensitivity - Broad (speech mode): 93 dB (2 kHz – 5 kHz)
(music mode): 90 dB (150 Hz– 18 kHz)
Sensitivity - Asymmetrical Progressive-Gradient Mode
(on-axis)
(speech mode): 94 dB (2 kHz – 5 kHz)
(music mode): 91 dB (150 Hz – 18 kHz)
Nominal Impedance (direct) 8Ω per half (top and bottom) for 4 ohms total (in thru mode).
Min-Z for system = 2.9Ω.
Hookup Ensure identical polarity of hookup – for proper functioning, the two loudspeaker modules (top and bottom) must be hooked up in same polarity. Parallel hookup at the two sets of back panel input terminals is recommended.
Power Capacity (thru setting) 650W (2600W peak), 2 hrs
400W (1600W peak) 100 hrs
Max SPL - Narrow (speech mode): 123 dB cont ave (129 dB peak)
(music mode): 120 dB cont ave (126 dB peak)
Max SPL - Broad (speech mode): 121 dB cont ave (127 dB peak)
(music mode): 118 dB cont ave (124 dB peak)
Max SPL - Asymmetrical Progressive-Gradient Mode
(on-axis)
(speech mode): 122 dB cont ave (128 dB peak)
(music mode): 119 dB cont ave (125 dB peak)
70V/100V Transformer Type Set individually per speaker module (top and bottom): 120W, 60W, 30W (15W at 70V only), and direct 8Ω, via switch. Total (with top & bottom set to same): 240W, 120W, 60W (30W at 70V only) and direct 4Ω. Max. insertion loss less than 1 dB at any tap.
Enclosure Fiberglass reinforced ABS cabinet, painted aluminum grille
Connectors Two (one for top half and one for bottom half), screw-down terminal strip, zinc-plated copper base, nickel plated metal screws/washers. Accepts up to 9 mm outside 4 mm inside open lug (#6, #8 or #10 lug), or bare wire (up to 12 AWC/2.5 mm2)
Outdoor Capability IP-55 rated, per IEC529, when installed with optional MTC-PC2 panel cover. UV, moisture and 200-hr ASTM G85 acid-air/salt-spray resistant.
Colors Black or White (-WH)
Configuration Two pieces (top and bottom half), each 100 cm tall, connected together via Coupler Plate. Top/bottom orientation of each piece must be observed.
Insert Points 28 M6 insert points on back panel (36 total with 8 center points being utilized by the Coupler Plate).
Mounting Included swivel (pan) / tilt wall bracket (must be mounted to threaded points on Coupler Plate) provides continuously variable ±80° left-right swivel aiming (at up to ±5° up/down tilt), continuously adjustable ±10° up/down tilt, as well as 5° fixed increment tilt angles to ±10°. Twenty-eight available threaded mounting points (M6 diameter x M1 thread pitch x 17 mm deep) located on back panel. Threaded mounting points can be utilized for suspension. Compatible with OmniMount 30.0 brackets
Dimensions (H x W x D) 2000 x 98.5 x 153 mm (78.8 x 3.8 x 6.0 in)
Net Weight 14.6 kg (33 lb)
Included Accessories Swivel (pan) / tilt wall bracket, Coupler plate
Optional Accessories MTC-PC2 terminal panel cover
MTC-CBT-FM1 flush-mount low-profile wall-mount bracket (2 pieces required)
MTC-CBT-SMB1 stand-mount bracket for use with 35 mm speaker stands (heavy duty stand required)

Det finnes ingen relaterte produkter.